Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
handheld device programming
”
RELATED FAQS
Question
Answer
Why would an LCN 8310-865 RF Receiver have a flashing "RED" light?
Resolution:
When the "RED" LED on the 8310-865 RF Receiver is blinking, it is receiving an RF signal (interference) from a non programmed device. When receiving this type of signal, it will not ...:
What do I need to get started in installing and programming the BE367?
Resolution:
You will need a HHD device, a CIP reader and CIP cable. If your computer does not have a DB9 which is the D shaped connection on the back of your computer you will need to get a converter. Th...:
How do I program Locknetics CM / CL legacy locks with the Schlage Utility Software (SUS) and Hand Held Device (HHD)?
Resolution:
- With the CIP NOT inserted and the Schlage Utility Software (SUS) running o Enter the Master Programming PIN or Present Loc...:
Can I have multiple Hand Held Devices (HHD) coupled to the same lock?
Resolution:
The Coupling Password is compared whenever an HHD is trying to adjust lock configuration settings or downloading door programming files.:
How do I manually change PIN length on an AD200?
Resolution:
Beginning with Firmware Packages ADFwPkg 2.16.3 and COFwPkg 1.20.0 the PIN length can be manually changed for AD200 and CO200 locks as follows: 1. Press {programming code (default is 97531)} then ...:
Why doesn't my AD lock go into Construction Mode?
Resolution:
Update your device firmware to the latest version to fix this early design / feature update:
How do I manually program the AD300 RS-485 Address?
Resolution:
Manually Setting the RS-485 Address This method is only available before the first network communication between an Access Control Panel (ACP) and the lock. Do a Level 1 and Level 2 Factory De...:
Can I use a SNAP programmer to program your FE210 or BE367?
Resolution:
Yes, although using the SNAP programmer is not recommended, because it is more difficult to program through the computer. In addition, Schlage no longer sells the SNAP programmer. The be...:
How do you program the 8310-877 safety sensor?
Resolution:
The 8310-877 safety sensor can only be programmed by using the 8310-859 remote. You can not manually program the 8310-877 safety sensor. However, you only need (1) 8310-859 remote to program any nu...:
BM-150 HHD
Resolution:
Windows CE based handheld device to support Schlage Utility Software (SUS).:
SUS
Resolution:
The Schlage Utility Software (SUS) is a software application that runs on a Windows CE based handheld device. It is used to transfer data files between the access control software and locks and con...:
BM-170 HHD
Resolution:
Windows CE based handheld device to support Schlage Utility Software (SUS).:
How does Dynamic Channel Switching (DCS) work on the AD-Series?
Resolution:
Setting Dynamic Channel Switching 1) Connect and couple the SUS to the PIM400 you intend to change. See the SUS User Guide for details 2) Under “PIM Properties” and the “Edit” tab is ...:
How many door files should the Hand Held Device (HHD) be able to store at one time?
Resolution:
For best Schlage Utility Software (SUS) and Hand Held Device (HHD) performance do not put more than 100 door files at a time ....:
How do I program my device?
Resolution:
The programming processes for Allegion devices can be both product and features specific. Some products programming processes are electronic in nature, others are physical in nature. &nb...:
Why do I get error message "E701 - Programming Lock Failed" on my Hand Held Device while programming an AD lockset?
Resolution:
Update your lockset using ADFwPkg 2.19.0 or higher. This new firmware update resolves this programming error problem (E701) and the error will no longer be presented.:
Restore/Reset Master Programming Code on DKP-165 Keypad
Resolution:
Power down the keypad then remove both JP1 & JP2 internal jumpers. Power up the keypad and wait a few seconds, the keypad will beep. Power down again, then reinstall the jumpers. Power back on....:
How do I clear the memory on a CT500?
Resolution:
To clear the memory on a CT500 controller, deleting all programming and codes from the controller and resetting to factory defaults, perform the following procedure: 1. ...:
Replacement BNC Cable for SNAP Programmer
Resolution:
This product is obsolete and is no longer available from Schlage Electronics.:
What versions of Microsoft Windows are compatible with Schlage Express version 4.4.2?
Resolution:
Microsoft Windows 8, 7, Vista, and XP: Home, Basic, and Starter versions are not compatible with Schlage Express. What versions of Microsoft Windows are compatible with Schlage Express v...: