Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
Ives hinge pin size
”
RELATED FAQS
Question
Answer
What is the part number for the rubber tip for an Ives hinge pin door stop?
Resolution:
Model 69 the part number is 09-310Model 70 & 73, the part number is WSPART.1075:
Does Steelcraft use a 7 gage hinge reinforcement on their frames?
Resolution:
Steelcraft uses a 7 gage hinge reinforcement for 4 1/2" and 5" butt hinges as standard on all frame series. The hinge reinforcement size for either 4 1/2" or 5" hinges (standard or heavy duty hing...:
What is the standard screw size used on Steelcraft doors with 4 1/2" or 5" hinges?
Resolution:
Steelcraft follows the industry standards for hinge reinforcement and preparation for both door and frame. Unless otherwise specified all products prepared for butt hinges will have mounting holes ...:
Does Ives offer a continuous hinge or pivot for lead lined doors?
Resolution:
Ives does not offer a continuous hinge designed specifically for lead lined doors. Standard hinges may work if the hinge and mounting hardware do not penetrate the lead lining in the door.&nb...:
CM Lock Manual Programming Disabled
Resolution:
When trying to program a CM lock, it may display an error code with a solid green light and 10 read flashes. This indicates the lock has already been programmed with computer software and manual ...:
Why are the bolts larger on the 8102, 8103, 8103EZ, 8190, 9100, 9103EZ, 9190?
Resolution:
In an effort to continue providing the highest quality products and align with market demand Ives has upgraded the mounting screws provided for the majority of 8000 and 9000 series pulls.The new an...:
How do you identify what size a 2030 closer is?
Resolution:
The Date Code and Closer Size are stamped in the backside of the closer body. These stamps will be on a smooth machined surface of the cylinder.Closer Size:If the number is "1", the...:
Can a 4040XP Pull Side closer be mounted with Swing Clear Hinges?
Resolution:
ST-1583 is used to template a 4040XP closer mounted hinge side with swing clear hinges. This ST is templating only – it uses standard parts.For current ST add on pricing and temp...:
Can a 4010 be mounted with swing clear hinges?
Resolution:
Locate closer and arm from the centerline of the swing clear hinge pin.:
Do we offer the Ives butt hinges in 609 finish?
Resolution:
The 609 finish is not available with Ives butt hinges.:
Where is common cutout for Von Duprin EPT prep in Ives 224 Continuous Hinge?
Resolution:
Cutout depends on the size of 224 hinge. See 112HD/224HD-EPT template. 112HD/224HD continuous hinge Center line of EPT to top of the door 83 inches 30 inches 85 inches 32 inc...:
What is maximum width, height and weight for IVES butt hinges?
Resolution:
Butt hinges can be used on doors up to 4' wide and 200 pounds. There is no maximum door height. However, an additional hinge must be installed every 30" when exceeding a 7' d...:
What is the hinge backset for 1 3/4" thick door?
Resolution:
Hinge backset is the dimension from the leading edge of the hinge to either the stop on the frame or to the stop face (push side) of the door. For operating clearance, the hinge backset on the d...:
What is the difference between the FE and DE-Series frames
Resolution:
A Double Egress frame is a double door frame prepared to receive two single-acting doors swinging in opposite directions (both doors are) the same hand. These openings are installed in cross corrid...:
What is Steelcraft's standard hinge locations for a 6'8" high frame from head to top of each hinge?
Resolution:
The location to the top of hinge will vary depending on hinge size used. 6'8" Frame with 1 1/2 pair of hinges (top to top): For 4 1/2" hinges from the head to top of each hinge is 7 1/2", 37 7...:
Does the wire size of an EPT affect the operation of an EL device?
Resolution:
Since most wire transfer devices such as an EPT or electric hinges cannot provide large gauge wires, we take the small gauge wire into account when determining the overall wire size for the device....:
What is the standard downsizing for a door leaf when using continuous hinges?
Resolution:
Doors require special downsizing for continuous hinges. The amount of downsizing depends on the hinge specified (manufacturer and type) and the hinge application (Full Mortise versus Full Surface v...:
Can you use a 4040SE with swing clear hinges on the pull side?
Resolution:
Push Side Mount: Take the dimensions for the closer and track from centerline of swing clear hinge pin for the push side mount.:
What is the part number for a control pin for a 23-030?
Resolution:
There are two parts that can be referred to as control pins for a 23-030 (FSIC core).C603-967 is the lower control pin that sits in the seventh hole of the FSIC plug. (part B in exploded view) ...:
Does Schlage offer a 7 pin FSIC?
Resolution:
The Schlage Full Size IC core is 6 pin only. :
How do I program Locknetics CM / CL legacy locks with the Schlage Utility Software (SUS) and Hand Held Device (HHD)?
Resolution:
- With the CIP NOT inserted and the Schlage Utility Software (SUS) running o Enter the Master Programming PIN or Present Loc...:
Does the Schlage SFIC rim housings accept both 6 and 7 pin IC cores?
Resolution:
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.:
Is a standard cylinder keyway such as "C" available in SFIC?
Resolution:
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system. A keyway name may be shared between the two key fami...: