Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ What is required with RF ”

RELATED FAQS

Resolution: RF sequential operation requires the use of of a minimum of 2 receivers (8310-865). Depending on the desired operation required (if using access control), it may require up to 4 receivers (8310-865...:

What components are needed to convert a hard wired actuator button to a wireless actuator button?

Resolution: To convert an RF actuator button to a hard wired actuator button, simply remove the RF transmitter an connect the hard wiring to the "Common" and "Normally Open" terminals on the the switch.:

Can a magnet, or sentronic device, be released and close the door from a button at a desk?

Resolution: If a door is being held open by the LCN SEM 7800/1900 magnet or any ME/SE Series Sentronic LCN closer, you can remotely release that door to close by ordering the following parts and wiri...:

Will a new RF "programmable" transmitter work with an older RF receiver that has "dip switches"?

Resolution: The newer "programmable" RF transmitters/receivers will not work with the older "dip switch" transmitters/receivers. The frequency and coding are different.:

How does Dynamic Channel Switching (DCS) work on the AD-Series?

Resolution: Setting Dynamic Channel Switching 1) Connect and couple the SUS to the PIM400 you intend to change. See the SUS User Guide for details 2) Under “PIM Properties” and the “Edit” tab is ...:

Why can't I LINK my AD-Series lock?

Resolution: 4. PIM400/AD400 COM400 plug could be damaged! The small pins in the Main PCB board connection for the RF COMM board can get bent during installation of the RF COM400 board. If the PINs are be...:

What is the new number for a 7910-931 receiver?

Resolution: The obsolete 7910-931 receiver has been replaced by the 8310-865 receiver.Replacing the receiver requires you to also replace the obsolete 7910-444 transmitter module with the 8310-844 transmitter.:

What is a 7910-967?

Resolution: The 7910-967 is a part number for a discontinued RF actuator. It was replaced by the 8310-3856WS RF actuator. The new 8310-3856WS requires the use of an 8310-865 RF receiver. When replacing the ol...:

Are the wireless RF Communication boards effectively equal and compatible with the Wireless products line

Resolution: Yes, all COM400 communications boards are compatible and interchangeable.2.2a, 2.2d, 2.3a are the possible version currently in the field with 2.3a in current production:

Can I get a Senior Swing with a reduced opening force gearbox?

Resolution: The older model Senior Swing came with 2 spring options. The "standard force" spring required 15 lbs of manual opening force, and reduced force "RF" required 11 lbs of manual opening force. All S...:

How many actuators can you have programmed on an 8310-865 receiver?

Resolution: The 8310-865 RF receiver can have up to 100 transmitters programmed to it.:

Why would an LCN 8310-865 RF Receiver have a flashing "RED" light?

Resolution: When the "RED" LED on the 8310-865 RF Receiver is blinking, it is receiving an RF signal (interference) from a non programmed device. When receiving this type of signal, it will not ...:

What is a Senior Swing 9540 RF?

Resolution: The Senior Swing Series used to have a 2 gearbox options, a "standard force" (15 lbs) and a "RF - reduced force" (11 lbs). In November 2009 RF option was eliminated and we made the standard sr...:

How do you program the 8310-865 RF receiver?

Resolution: To program the 8310-865 receiver: Set the dip switches 1 to the "OFF" (pulse) position. Set the dip switches 2 to the "OFF" (0.5s) position. Momentaril...:

Resolution: Radio Frequency:

What are the TWO red SCHLAGE flashes on an AD400?

Resolution: ONE red flash, One red flash indicates RF COM loss, the AD400 radio did not get an answer from the PIM400-485 radio or the PIM400-TD2 radio. The PIM400-485 will turn off it's radio if th...:

What is the part number for the wireless communication module, radio board, COM400, with the remote antenna connection (gold jack)?

Resolution: The COM400 has only two versions of FW, 2.2a and 2,2d and they are cross compatible and completely functional with all AD-Series wireless devices. There is no reason to change a FW 2.2a to a FW 2...:

How do I change an AD-Series lock to a different AD-Series lock type?

Resolution: Re-classing is the process by which an AD-Series device is able to change its lock type. The AD-Series has a modular architecture and a major benefit of this type of architecture is that it allows ...:

What is the read range of the new Schlage MT11 wall mounted reader?

Resolution: All read ranges are affected by the environment the reader and card are subjected too. The following data was obtained in a relatively "noisy" RF area with the reader mounted on a metal ...:

What is Z-Wave Technology?

Resolution: Z-Wave is a mesh networking technology developed in 1999 to create a standard for wireless radio frequency (RF) communication for home devices. The key to the technology is that Z-Wave products are...:

How does Cache mode work on AD400 and AD300 locksets?

Resolution: An AD400 granting credentials access in “cache mode” will blink the Schlage with the normal green LED, followed by a brief red Schlage LED flash, indicating no RF communication and access was grant...:

What is the read range of the Schlage MT11 wall mounted reader?

Multi-Technology Cards

Resolution: A card or credential utilizing two or more technologies such as magnetic stripe and proximity (RF).:

FCC Certification

Resolution: U.S. certification indicating that a product meets FCC standards regarding RF signal interference.:

Can a wireless actuator be converted to hardwired?

Resolution: Yes. Remove the receiver from the operator. Remove the transmitter from the actuator button. Attach 1 wire to the NO (normally open) contact on the actuator switch, and another wire to the COM (com...:

RADIO FREQUENCY

Resolution: RF, wireless activation:

Can I make a wireless activated 4640 operator work as alternate action?

Resolution: The 8310-865 RF receiver contacts (N.O. and COM) would connect to terminals 15 & 17 (the alternate action input) on the 4600 operator. The first activation would open the door, the s...:

PIM400-485

Resolution: Panel Interface Module which receives RF communications from an AD400, WRI, or WPR, and interfaces, via wiring, to the RS485 port of an OEM partner Access Control panel.:

Can hardwire actuators and wireless actuators be used together on an operator?

Resolution: Hardwired and RF actuators can be used together on the same operator. The hardwired switch and the RF receiver both provide a N.O. contact to the operator.:

PIM400-TD2

Resolution: Panel Interface Module which receives RF communications from an AD400, WRI, or WPR, and interfaces, via wiring, to the wiegand input of an access control panel.:

What does a blinking TROUBLE LED (D1/D2) mean on my PIM400-TD2?

Resolution: a) One blink of the TROUBLE LED means the AD400 on this channel has low AA batteries. Install fresh batteries. b) Two blinks of the TROUBLE LED means the AD400 on this channel is not communicating...:

CE Mark

Resolution: European certification that products meet RF interference standards (see also FCC certification).: